CASE STUDIES · WORKED EXAMPLES

Real parts. Clear design decisions.

Worked examples across railway, oil and gas, automotive and construction. Each one starts from how the part works and ends with a change you can build.

4Industries
1Method on every part
PDFFull study on request
1 dayReply time
THE LIBRARY

Pick your industry.

Each card shows the question we were asked and the decision the analysis led to. The full study has the loads, the model, the results and the test plan.

Three-piece freight bogie side frame and axle boxR-01
Railway

Suspension spring stack for a freight bogie

A spring stack that loses preload stops damping. How much set can it take?

Grade and seat design keep the strain inside the PU limit for the full endurance run, with a maintenance rule tied to preload.

12.4 %
average strain at full load
+65 %
extra travel if the faces slide
Similar part?
Freight wagon bogie with side frame and springs on the trackR-02
Railway

Bonded suspension layer for a freight bogie

Soft enough to let the wheelsets steer, stiff enough to stop them hunting.

Two options with the same steering stiffness and up to 40 % less strain at the bond.

-40 %
strain at the bond
5
elastomers compared on one model
Similar part?
Rail fastening on a sleeper over ballastR-03
Railway

Grooved track fastening element

The compound alone cannot hit the stiffness window. Can the groove pattern?

Groove pattern and hardness tolerance put the part in the middle of its window, decided before the mould was cut.

10x
softer than the same compound without grooves
75 %
rib contact that centres the design
Similar part?
Coupler between two railway vehiclesR-04
Railway

PU energy absorber for coupling impacts

How many pads, which grade, and what impact can the stack take?

One standard 90A pad design meets the energy and force brief. 95A does not suit this geometry.

18
pads of one standard design
7.2 km/h
impact speed absorbed
Similar part?
Engineer beside large line pipe sections on siteO-01
Oil & gas

Pipeline pig sealing disc

Seal too lightly and fluid bypasses. Seal too hard and the pig stalls.

The grade, not the oversize, sets the drag.

0.16 bar
driving pressure per 80A disc
2.5x
drag with the stiffer grade
Similar part?
Industrial gate valve with handwheel and bolted bonnetO-02
Oil & gas

O-ring in a high-pressure gland

At what pressure does each hardness start to extrude into the gap?

90A with a tight gap holds 20 MPa. The 40 MPa gland needs a back-up ring.

3x
extrusion resistance, 90A over 70A
40 MPa
gland specified and sealed
Similar part?
Offshore production platform at seaO-03
Oil & gas

Bend stiffener for a flexible riser

Keep the riser above its bend limit, in warm and cold water.

A 1.5 m PU cone lifts the tightest bend from 0.73 m to 2.9 m.

4x
larger bend radius
9.5 %
peak strain in the PU
Similar part?
Coil spring and damper of a car suspensionA-01
Automotive

Cast PU suspension bumper

Can we predict the force curve from the CAD model, before the mould exists?

Yes. The model moved the redesign to the bore and nose before the mould was machined.

4.0 kN
force where the folds start to close
60 %
local strain found at the nose
Similar part?
Open engine bay of a carA-02
Automotive

Powertrain mounting system

Why does the body shake every time the engine starts?

Mount rates and heights retuned until the torque roll mode stood on its own.

46 to 90 %
roll mode purity
-37 %
shake at start-up
Similar part?
Car on a lift showing the suspension and wheelA-03
Automotive

Control arm bush with voids

Soft for comfort in one direction, stiff for steering in another.

One rubber part with a 6.6 to 1 stiffness split and a progressive stop at about 3 mm.

6.6 : 1
radial stiffness split
2.9 mm
travel before the stop
Similar part?
Underside of a concrete viaduct with girders on piersC-01
Construction & mining

Laminated bridge bearing

Which design check really governs, and how much rubber can go?

Resized from 320 x 500 to 280 x 450 mm. Every check passes with margin.

-22 %
rubber and force on the pier
62 %
highest check utilisation
Similar part?
Conveyors and vibrating screens at an aggregate plantC-02
Construction & mining

Modular PU screen panel

Is strength really what limits a panel on a vibrating screen?

No. Sag and wear do, and clamping the edges is the cheapest fix.

66 to 89 Hz
first mode, clear of the 15 Hz screen
-26 %
open area lost with thicker bars
Similar part?
HOW EVERY STUDY WORKS

Same method on every part.

01

Understand the job

Loads, travel, environment and the standard the part must pass.

02

Model it simply

The simplest model that answers the question, and no simpler.

03

Prove the model

Every solver checked against a known answer before we trust it.

04

Decide and test

A grade, a dimension or a maintenance rule, then a test on prototypes from our own moulds.

Want to see one part go through every stage? Open the live 3D demo →

GET THE FULL STUDY

Pick a study. We send the full PDF.

One study per request. Add your details and we email the PDF within one business day.

Each full study covers

  1. 01
    How the part worksIts job in service and what it must survive.
  2. 02
    The modelHow we built it and how we checked it.
  3. 03
    The resultsWhat the analysis showed, in charts and numbers.
  4. 04
    The decisionThe design change and how we validate it.
Study you want * One per request
Railway
Oil & gas
Automotive
Construction & mining

We respond within one business day. Or use the full quote page.

Photographs: Pexels and Unsplash contributors under their free licences. Case figures are summaries; each full study lists its inputs, assumptions and references.